- Articulating mounting platform for integration with select model Juggernaut cases (see Complete Your Kit section below)
- Includes red LED back lit oil-filled Oceanic compass
- Provides mounting tabs for Garmin GPS 401/601/701 (Garmin not included)
- Includes integrated case heater with CR123 Battery_Module/Cable
- Incorporates stylus holder with tether
- Provides low-profile, stowable hinged platform for use under canopy
- Allows for situational awareness and visibility of landing zone
- Only available in black
- Designed, engineered and packaged in the USA from global components
- Standard lead time is 12-14 weeks
-
-
- Dual captive thumbscrews for secure attachment
- Sealed gasket for IP-67 rated connection to case
- Shielded against EMI/RFI
- Overmolded strain relief
- Designed, engineered and packaged in the USA from global components
-
- Ruggedized polymer HAHO freefall accessory
- Integrates with PALS Armor Mount or HAHO Sternum Mount, and any of our smartphone case models (sold separately)
- 5 series fits the 4.5" and 5" PALS or HAHO sternum mounts. 6 series fits the 5.5" and 6" PALS or HAHO sternum mounts
- Includes red LED back lit oil-filled Oceanic compass
- Provides mounting tabs for Garmin GPS 401/601/701 (Garmin not included – optional add-on)
- Provides low-profile, stowable hinged platform for use under canopy
- Allows for situational awareness and visibility of landing zone
- Can be used as stand-alone device when routed through container strap (not typically a military approved configuration)
- NSN# 5895-01-671-8314 (FDE, 5"), 5340-01-672-6079 (FDE, 6")
-
- EUD is power sink and data host
- 7.5W charge rate when attached to 5V source
- Terminates to sealed 807 series connector
- Dual captive thumbscrews for secure attachment to any SLEEV or OPRTR case model (replaces QD Door)
- Sealed gasket for IP-67 rated connection to case
- Secondary IP-67 deal to USB-C port on smartphone or tablet
- Shielded against EMI/RFI
- Overmolded strain relief
- Polyurethane jacket
- Designed, engineered and packaged in the USA from global components
- Not optimized for use with StarPan hub (please contact Glenair for Juggernaut compatible cable)
-
Technical features:
- Zipper: YKK AquaSeal #10, 300mBar airtight
- Coating:Thick double sided TPU laminated
- Fabric: 840 denier 6.6 HT Nylon
- Foam:Dual density EVA shoulderstraps for comfort
- Reinforcement: Vulcanized rubber
- Frame: HDPE and EVA foam
-
Out of stock
- Kit includes tablet SLEEV
- Robust, ergonomic two-strap kneeboard mount
- Withstands the 650kt blast during ejection from a fixed wing aircraft (EjectionSeat Windblast Tested/Approved)
- Tablet case is bolted into the mount platform
- Secondary 1" strap to keep the EKB from sliding down the pilot's leg during normal egress from the cockpit
- Underside of mount is padded with ToughTek No-Slip material
- Features ITW-Cobra Buckles on leg straps
- NSN# 7045-01-676-9842 (FDE, 7.5"), 7045-01-677-0426 (FDE, 8")
-
Technical features:
- Zipper: YKK AquaSeal #10, 300mBar airtight
- Coating:Thick double sided TPU laminated
- Fabric: 840 denier 6.6 HT Nylon
- Foam:Dual density EVA shoulderstraps for comfort
-
- Compatible with goTenna Pro, Pro X, and Pro X2 mesh radios (not included)
- Connects with our Source mode cable (QD or IMPCT models)
- Allows mesh network capability in an off-grid environment without cellular, Wi-Fi or satellite
- TPU jacket
- Shielded and IP67 rated when connected
- Designed, engineered and packaged in the USA from global components
-
- EUD is power sink and data peripheral
- Terminates to sealed 807 series connector
- Dual captive thumbscrews for secure attachment to any SLEEV or OPRTR case model (replaces QD Door)
- Sealed gasket for IP-67 rated connection to case
- Secondary IP-67 deal to USB-C port on smartphone or tablet
- Shielded against EMI/RFI
- Overmolded strain relief
- Polyurethane jacket
- Designed, engineered and packaged in the USA from global components
-
- EUD is power source and data host
- Terminates to sealed 807 series connector
- Dual captive thumbscrews for secure attachment to any SLEEV or OPRTR case model (replaces QD Door)
- Sealed gasket for IP-67 rated connection to case
- Secondary IP-67 deal to USB-C port on smartphone or tablet
- Shielded against EMI/RFI
- Overmolded strain relief
- Polyurethane jacket
- Designed, engineered and packaged in the USA from global components
-
- Fits iPad Mini, version 5 (does not fit earlier generation 1-4)
- Foam gasket seal to touchscreen (no glass screen cover)
- 2M Drop Protection
- Compatible with Tablet-MEDIUM (8) mounts
-
Weight: 1750g Dimensions: L70 × W43 × H32 cm Design Features:
- 2 carry handles on each end
- Daisy chain on both sides for quick attachment
- Adjustable and removable shoulderstaps
- Safe and lockable zipperhead for flights
- Oral valve to compress or inflate with air
- Zipper:YKK Aquaseal #10, 300mBar airtight
- Coating:Double sided TPU laminate
- Fabric:840 denier 6.6 HT Nylon main. 420 6.6 HT Nylon side
- Foam:Dual density EVA shoulderstraps for comfort
-
Weight: 1400g Dimensions: L63 × W36 × H28 cm Precise volume: 61L Design Features:
- 2 carry handles on each end
- Daisy chain on both sides for quick attachment
- Adjustable and removable shoulderstaps
- Safe and lockable zipperhead for flights
- Oral valve to compress or inflate with air
- Zipper:YKK Aquaseal #10, 300mBar airtight
- Coating:Double sided TPU laminate
- Fabric:840 denier 6.6 HT Nylon main. 420 6.6 HT Nylon side
- Foam:Dual density EVA shoulderstraps for comfort
-
- Shielded Extension Cable for all Nett Warrior compatible cables with Glenair 6 pin 807 connector
- IP-67 rated
- Available in 24" or 36" lengths
- Designed, engineered and packaged in the USA from global components
- Works with any mode (Sink, Source, Power Delivery)
-
- Fits Samsung Galaxy Tab Active 2 Rugged Tablet (SM-T390N) without the Elastomeric Bumper
- Foam gasket seal to touchscreen (no glass screen cover)
- Rugged frame with open access to rear battery cover without removal of device
- 2M Drop Protection
- Cable housing for use with optional QD (Quick Disconnect) cables
- Compatible with Tablet-SMALL (7.5) mounts
- Rated to 9G's when installed in mounts
- S-Pen storage inset on top door of SLEEV
- NSN# 7045-01-679-7945 (FDE)
-
- Fits Samsung Galaxy Tab Active 3 Rugged Tablet without the Elastomeric Bumper
- Foam gasket seal to touchscreen (no glass screen cover)
- Rugged frame with open access to rear battery cover without removal of device
- 2M Drop Protection
- Cable housing for use with optional QD (Quick Disconnect) cables
- Compatible with Tablet-SMALL (7.5) mounts
- Rated to 9G's when installed in mounts
- S-Pen storage inset on top door of SLEEV
-
- Snap-In USB-C docking cable assembly (replaces IMPCT dust cover)
- Shielded against EMI/RFI
- Closed cell foam seal provides IP-67 seal between case & connector assembly
- Overmolded strain relief
- Designed, engineered and packaged in the USA from global components
- Cables with 807 series Glenair 6 pin Mighty Mouse connector are Nett Warrior compatible
-
Technical features:
- Zipper: 2 way lockable #10 YKK Coil
- Coating: Double sided TPU laminate base
- Fabric: 1000 denier Cordura
- Foam: Dual density EVA shoulderstraps for comfort
-
- Intended for custom development by integrators
- Pass thru 3.1 speed
- 16 wire with cut/flying lead
- Dual captive thumbscrews for secure attachment to any SLEEV or OPRTR case model (replaces QD Door)
- Sealed gasket for IP-67 rated connection to case
- Secondary IP-67 deal to USB-C port on smartphone or tablet
- Shielded against EMI/RFI
- Overmolded strain relief
- TPE jacket
- Designed, engineered and packaged in the USA from global components
-
Weight: 950 g Dimensions: L55cm x W30cm x H32cm / L21.5” x W12” x H12.5” Precise Volume: 50 Liters / 3050 CU IN Design features:
- Quick release shoulder straps with 2M ROC buckles
- Inner side-wall zippered pockets
- Carry handles on each short end
- Lightweight & waterproof 420 denier HT Nylon fabric with double TPU coating
- Rubberized reinforcement fabric with embossed Halite logo on the bottom
- TIZIP® #10 MasterSeal Waterproof Zipper (500 mbar)
- RF Welded waterproof construction
- Deflation valve
-
- Terminates to standard commercial USB-A connector (not sealed on that end)
- Dual captive thumbscrews for secure attachment to any SLEEV or OPRTR case model (replaces QD Door)
- Sealed gasket for IP-67 rated connection to case
- Secondary IP-67 deal to USB-C port on smartphone or tablet
- Shielded against EMI/RFI
- Overmolded strain relief
- PVC jacket
- Designed, engineered and packaged in the USA from global components
-
- Fills gap between short duration 24HR Assault Pack and full size rucksack
- Internal frame sheet
- Ergonomically shaped aluminum wire frame
- Top loading, PALS panels on the sides
- Top pocket with small electronics pocket and two daisy chains
- Two hip climbing gear attachment loops
- Two top hauling handles
- Internal VELCRO® Brand panels for gear organization and a water bladder pocket
- Webbing on top for attaching crampons of other equipment
- 100% Made in the USA
-
- Fits Samsung Galaxy S8 (SM-G950A)
- Designed for devices that are already environmentally sealed
- Foam gasket seal to touchscreen (no glass screen cover)
- 2M Drop Protection
- Cable housing for use with optional QD (Quick Disconnect) cables
- Compatible with size MEDIUM (5) mounts
-
- Fits Samsung Galaxy S9 (SM-G960A)
- Designed for devices that are already environmentally sealed
- Foam gasket seal to touchscreen (no glass screen cover)
- 2M Drop Protection
- Cable housing for use with optional QD (Quick Disconnect) cables
- Compatible with size MEDIUM (5) mounts
- NSN# 5975-01-683-1076 (FDE)
-
- Fits standard Samsung Galaxy S10 (not Plus, E or 5G)
- Designed for devices that are already environmentally sealed
- Foam gasket seal to touchscreen (no glass screen cover)
- 2M Drop Protection
- Cable housing for use with optional QD (Quick Disconnect) cables
- Compatible with size SMALL (4.5) mounts
-
Out of stock
- Fits Samsung Galaxy S20 (does not fit S20+, S20 Ultra, S20 FE, or the Note 20 series)
- Designed for devices that are already environmentally sealed
- Foam gasket seal to touchscreen (no glass screen cover)
- 2M Drop Protection
- Cable housing for use with optional QD (Quick Disconnect) cables
- Compatible with size MEDIUM (5) mounts
- NSN #: 5895-01-694-7436
-
- Fits Samsung Galaxy S21 (does not fit S21+, S21 Ultra)
- Designed for devices that are already environmentally sealed
- Foam gasket seal to touchscreen (no glass screen cover)
- 2M Drop Protection
- Cable housing for use with optional QD (Quick Disconnect) cables
- Compatible with size MEDIUM (5) mounts
-
- Compatible with the Juggernaut.Case Sink Mode cables
- Ideal for connection to external batteries, computers and vehicle power sources
- Sealed on 807 connector end, but not on USB-A end
- 36" length
- PVC jacket
- Shielded, 2.0 compliant
- Designed, engineered and packaged in the USA from global components
-
- Low-Visibility Stealth Trauma Aid Minimalist Pack
- Hooks directly to duty belt with IWB belt loop connectors
- Moisture resistant, lightweight
- Shock cord pull tabs for access to contents
- Center flap with hook and loop closure
- Optional Public Access Individual Bleeding Control Kit
- Material: pack cloth, 4” elastic, fiber-filled padding, and an air mesh interior
- Dimensions (WxHxD): 8 .5"x 4"(flaps folded down) x 3/8”empty
-
- Carries minimum amount of kit for short duration missions
- Carries 50-70oz water bladders
- Upper zipper pouch holds SOCOM issued NVG protective insert
- Removable medical pouch
- Attachment: PALS compatible Helium Whisper® system
- 100% Made in the USA
-
SPECS
- 4.4 ounces, 7.02" x 3.58" x 0.69"
- Not applicable
- 4202122120
- USA
- MEDIUM
-
The OPRTR provides crucial device protection in scenarios where real time response is vital to your team’s coordination. We go well beyond MIL standard for drop protection, and offer mission-specific mount and cable solutions that interface with other essential tactical equipment.
- Fits Samsung Galaxy S22
- Designed for devices that are already IP68 rated
- Top load with locking dual latch door
- Hinged or removable Quick Disconnect door secured by thumbscrews
- Compatible with all Juggernaut Quick Disconnect (QD) cables
- QD door and cables seal to device
- Screen protector compatible with Juggernaut SHLD
- Lanyard attachment points
- Fits size MEDIUM mounts
-
- Compatible with limited IMPCT models
- Designed to emulate a desktop environment for vehicle operations, or provide a robust mounting/charging solution
- Allows user connectivity to hubs for operation of full-size display, keyboard, mouse and Ethernet network connection (like this Tough-Hub from RAM)
- Leverages Samsung DeX Mode (Desktop Experience) with the USB-C Female configuration (JG.CBL.DOCK.ICF)
- Other cable options provide charge (JG.CBL.DOCK.IA & JG.CBL.DOCK.ICM)
- Mount compatible with AMPS pattern or RAM 2x3 Ball Mount (not included)
- EMI/RFI shielding within cable to reduce signal interference in high noise environments
- Crash tested
